Welcome, Guest. Please login or register.
Did you miss your activation email?
May 02, 2025, 03:02:15 pm
Home Help Search Login Register

Ottawa Fiero Club Forum  |  Buy/Sell/Trade  |  Parts  |  Topic: Cleaning out sheds « previous next »
Pages: [1] Go Down Print
Author Topic: Cleaning out sheds  (Read 3358 times)
2ML67
Guest
« on: April 06, 2009, 03:36:31 pm »
I have begun fully cleaning out my parts sheds and need for some parts that are good to go.
Main part is a black GT (fastback) rear clip and a  red GT deck lid  also from a fast back.
I paid $140 for both and will take $140 for both or will find the room to store them.
I have all sorts of Fiero V6 parts like alt brackets and engine mounts that are of no use to me as well as heat shields and such also from the V6 Fiero engines.
Have one V6 Fiero Getrag that needs the input bearing sleeve replaced but other then that is in great shape.
One 88 4cyl Isuzu tranny with shifter cables that is in excellent shape from a running car that recieved a 3800SC swap.
Also one 99 GTP 3800SC engine with just over 240,000 km that needs a timing chaing and some new gaskets to make perfect for a Fiero swap.
Will list more parts as I dig them out. Dan   
Logged
2ML67
Guest
« Reply #1 on: April 07, 2009, 10:38:09 am »
More stuff, found a quad 4 5 speed Getrag that I was going to use for two of the gears in a V6 getrag but never got around to it that is in great shape as well as a 2004 Grand Am 3400 engine with only 125,000 km on it that also runs great that I was going to use for a Fiero swap if I ever found the time.
Also brown carpet and a brown dash in good shape and grey carpet and a set of two tone gray seats from an 85 GT that are in good shape.
Also a set of four 14" aluminum Fiero rims with good rubber that will pass safety on them along with a lot more parts. Dan
Logged
87GT
Fiero Owner
**
Offline Offline

Posts: 56
« Reply #2 on: April 07, 2009, 11:18:11 am »
Dan,

In your various parts bins, would you have any axle components to help with a 3900 V6 (from a 2006 Impala) swap into a Fiero.  I'm not sure of the splines / lengths right now but thought you might know?

The engine coming out is the 2.8 V6.

Gord
Logged
can machine
Moving UP!
****
Offline Offline

Posts: 382
« Reply #3 on: April 07, 2009, 12:29:09 pm »
P.M. Sent
Logged
Fred
Fiero Owner
**
Offline Offline

Posts: 93
« Reply #4 on: April 07, 2009, 02:43:01 pm »
P.M. Sent!  Grin
Logged
Pontiac Fiero GT 1987
Sentinel
Returns to active lurker status
Ottawa Fiero Member
MASTER FIERO
*****
Offline Offline

Posts: 621


Wrapped in Horsepower, Driving into Fury......
« Reply #5 on: April 08, 2009, 07:30:52 pm »
Your shed is like a Fiero lovers tickle trunk(hopefully everyone has seen Mr Dressup otherwise this is a rather awkward post.)
Logged
We drive so fast , it seems as though , we take into the sky, the Fiero Machines in Harmony , Hear the Engines Cry
Fred
Fiero Owner
**
Offline Offline

Posts: 93
« Reply #6 on: April 11, 2009, 10:28:39 pm »
Thanks alot Dan!  Wink

You have once again an other satisfied costumer!  Afro Keep on the good work! lol

Again, thanks for everything,
Fred
Logged
Pontiac Fiero GT 1987
va3jco
Guest
« Reply #7 on: April 13, 2009, 08:51:31 pm »
i am looking for shift cables from a 85 2m4 with a 5 speed?? any chance you have any, thanks Jamie  va3jco@yahoo.ca   or   613-312-9771
Logged
2ML67
Guest
« Reply #8 on: April 14, 2009, 09:00:47 am »
I just have the set of shifter cables that came with the Isuzu tranny and do not want to sell them with out the tranny. Dan
Logged
va3jco
Guest
« Reply #9 on: April 14, 2009, 08:24:55 pm »
how much? i'm on a very tight budget, trying to get this car back on road, it only has 96000km on it thanks Jamie
Logged
Pages: [1] Go Up Print 
Ottawa Fiero Club Forum  |  Buy/Sell/Trade  |  Parts  |  Topic: Cleaning out sheds « previous next »
Jump to:  


Powered by MySQL Powered by PHP Powered by SMF 1.1.18 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!